Most people don’t think about their hot water unit until it stops working, usually on a cold morning right when everyone needs a shower. The good news is that a simple service every few years can add years to the life of your system, keep your water safe, and help protect your manufacturer’s warranty.
Whether you’ve got an electric storage tank, a gas unit, solar or one of the newer heat pumps, the same rule applies: look after it, and it’ll look after you.
Why servicing matters for your warranty
Hot water manufacturers like Rheem recommend a major service every five years, carried out by a licensed plumber. Their warranty terms also expect the unit to be installed and maintained in line with their instructions.
What this means for you: if your tank rusts through because the anode was never checked, or a valve fails after years of neglect, the manufacturer may knock back your claim. A cylinder replacement isn’t cheap. A service is.
It’s worth knowing that the service itself and parts like anodes and relief valves are treated as routine maintenance, so they’re not covered by the warranty. Think of it like servicing your car: you pay for the oil change so the engine stays covered.
1. Replacing your anode after 5 years
Inside every storage tank (including heat pump tanks) is a long metal rod called a sacrificial anode. Its job is simple: it corrodes so your tank doesn’t. Over time it slowly gets eaten away, and once it’s gone, the water starts attacking the tank lining instead.
We recently pulled this one out of a heat pump on a job. The old anode on the left is badly corroded and almost spent, next to the brand new one on the right. Once an anode gets to this point, your tank has very little protection left.

How often it needs replacing depends on your water quality, but manufacturers generally call for the anode to be inspected and, if needed, replaced within five years. Hard or corrosive water can wear it out even faster.
Signs your anode might be finished:
- Rusty or discoloured hot water
- A rotten-egg smell from the hot tap
- Rumbling or popping noises from the tank
- It’s been more than five years since anyone checked
Replacing an anode costs a fraction of a new hot water system, and it can add years to the life of your tank.
2. Checking your PTR valve
The PTR (pressure and temperature relief) valve is the brass valve near the top of your tank with a small lever on it. It’s one of the most important safety parts on your system. If the pressure or temperature inside the tank gets too high, it opens and lets water out so the tank doesn’t fail.
Because these valves can seize or wear out over time, manufacturers recommend replacing the PTR valve as part of the five-yearly major service. During a service we’ll also check the drain line and the expansion control valve (if you have one).
What you can do at home: most manufacturers suggest gently lifting and lowering the easing lever on the PTR valve every six months to keep it moving freely. The water that comes out will be hot, so stand clear of the drain. If the valve keeps dripping constantly, or nothing comes out when you lift the lever, give us a call.
3. Checking your hot water temperature
Getting the temperature right is about two things: stopping bacteria and stopping burns.
- In the tank: at least 60°C. Hot water has to be stored at 60°C or higher to stop bacteria like Legionella growing in the system.
- At the bathroom taps: no more than 50°C. In Victoria, hot water to showers, baths and basins in new homes and renovations is limited to 50°C. At 50°C, it takes around five minutes to cause a serious scald. At hotter temperatures it can take as little as a second.
A tempering valve is what makes both possible. It mixes in cold water so the tank stays hot but the water at your bathroom taps is safe. These valves also need checking, and during a service we’ll test the temperature at your taps to make sure everything’s working as it should. This is especially important if you’ve got young kids or elderly family members at home.
What’s included in a Vanity Plumbing hot water service
- Inspect and replace the sacrificial anode if needed
- Replace the PTR valve
- Inspect and flush the expansion control valve (if fitted)
- Test the tempering valve and check the temperature at your taps
- Check the tank, fittings and drain lines for leaks or corrosion
- Drain and flush the tank if required
- Let you know honestly if anything else needs attention
When did you last have yours serviced?
If your hot water unit is coming up to five years old, or you can’t remember the last time anyone looked at it, now’s a good time to book a service. It’s a small job that can save you the cost and hassle of a full replacement down the track, and helps keep your warranty intact.
Vanity Plumbing services Torquay and the Surf Coast. Call 0452 547 189 or get in touch to book your hot water service today. You can also read more about our hot water repairs and installation.
Always check your own unit’s manual for the manufacturer’s specific maintenance and warranty requirements.


Leave a Reply